Table of Content
In the past walls were generally 4 inches thick but in recent years, as mobile homes have grown in dimension and size, this has tended to increase to 6 or 6 ½ inches. Most out-swinging doors are left-handed but in-swinging and combination doors generally swing both ways. If the door to be replaced is an external door, you will need to figure out if it is a standard out swinging door or a non-standard in-swinging door. This is different to regular homes where external doors generally always swing inwards. If it is out swinging, get your tape measure and measure the entire opening from inside the mobile home, again from wall to wall horizontally and top to ceiling vertically.
If you are looking for a mobile home door replacement for your patio, or even a mobile home back door, measurement and selection will be key. There are many different sizes to choose from, but first, we need to know how to properly measure your door. Many mobile homeowners make the mistake of measuring the door itself.
Other Doors
Apply a suitable non-hardening sealant tape to the backside of the door's mounting flange. Please contact us with any questions that you may have, to order a door, or to check what doors we have in stock. Misunderstanding about the swing direction in easy-to-understand terms."
Consider installing a chain latch on your door if you do not have a locking mechanism yet. You can also easily install a stainless steel deadbolt lock. This is a bit more expensive but has proven to be extremely effective in stopping unwanted guests from entering your home.
Common Issues with Mobile Home Doors
This gives you a rough starting point for the door’s dimension. It can help you figure out which size door you need. In presently so that you cannot see the door jamb, measure from the edge of the door's metal frame to the opposite side frame.
Obviously, the opening should be slightly larger than the size of door required to ensure the door fits and doesn’t overlap. This is most important if the door is made from wood which can expand and contract in certain weather conditions. If the door is made from prefabricated plastic, it will essentially come pre-made to fit the opening exactly if it is a standard size. If it is a non-standard size, a specialist door manufacturer and fitter may be required.
Taking Measurements For a Door:
Just to be safe, measure the area where your door will go, too. Record the height and width of the door frame space. This will help ensure that you select the exact right replacement door.
But how do you measure your mobile home doors and what things do you have to take into consideration? Let’s have a look in our comprehensive guide on how to measure your mobile home doors successfully. Measure the height and width of the framed door space.
If your door is currently out of alignment and you are looking for a mobile home door replacement, make sure you have leveled the home before attaching the new door. Otherwise, you will face very similar issues with your new door. If the inner door is secured to the jamb with butt type hinges , run one long screw through each hinge on the jamb side to penetrate the stud. Do not remove any shipping clips or fasteners and keep the door closed and locked during the installation. Opening the door prior to the installation will destroy the pre-squaring by the manufacturer.
Ideally you would measure the opening the door unit was going into both width and height making note if your walls are 4" deep or 6". That said, if you have a door already installed you cannot do this so we have two options to still obtain a good measurement. The first one you will go outside and close your front door. Facing the closed screen or storm door make a note as to what side your knob is on and the hinges.
The most common issues for mobile home doors come from an unlevel foundation in your mobile home. This will put pressure on the door frame, the door hinges, and the door itself. In more extreme cases of an unleveled foundation, the doorframe becomes crooked enough that closing and opening the door is extremely difficult. You may find that this issue is exacerbated in the fall as temperatures begin to decline.
This flange overlaps the wood of your door jamb, and is where you secure the aluminum frame to the door jamb with screws. So measuring to the edge of the jamb will give you a number larger than what you really need. To measure an outswing door simply open the door and measure inside of frame to inside of frame, to get as close to the rough opening size as possible.
Standard size mobile home doors are far cheaper than custom built ones, so if your door sizes are not standard, it can sometimes be cheaper to re frame the opening first. This is why its so important to know how to measure a mobile home door. These costs can all add up quickly if you don’t calculate right from the beginning.
No comments:
Post a Comment